Please or to access all these features

AIBU?

Share your dilemmas and get honest opinions from other Mumsnetters.

Does my kitchen worktops look properly fitted or aibu?

31 replies

ForeverQuery · 12/12/2021 11:59

Posting for traffic
Kitchen fit nearly complete but this is making me feel uneasy
Aibu?

Does my kitchen worktops look properly fitted or aibu?
Does my kitchen worktops look properly fitted or aibu?
Does my kitchen worktops look properly fitted or aibu?
OP posts:
New posts on this thread. Refresh page
AnnieAreYouOkHun · 12/12/2021 18:43

I've just asked dh opinion who's a joiner and he says it doesn't look like it's been cut with a jig and looks more like it's been hand cut but can't be sure without a clearer picture. He also said the joint itself when butted up should be no bigger than 0.5mm and the 2 worktops should be flush.

LazyDoll · 12/12/2021 18:32

I assumed it would be a straight edge to edge like here. But regardless it’s a very obvious join- I take it it’s stone? Ask for a remedial to sort it.

Does my kitchen worktops look properly fitted or aibu?
HoardingSamphireSaurus · 12/12/2021 15:28

@Ozanj

You shouldn’t need joins unless you’re using granite and have a really large space to cover. The fact that they gave them to you in such a small space suggests they’re probably using offcuts from someone else’s kitchen. I’d be raising hell about this.
Not sure that is possible. Think how big the sheet if whatever would have to be.

Most work surfaces have joins in corners, except the reconstituted, sometime slip over, made to measure ones.

Flowers500 · 12/12/2021 14:40

if you have an L shape (so a corner) there has to be a place where two different directions meet? I don't understand how they could avoid that?

Flowers500 · 12/12/2021 14:29

they're stone, aren't they? If so I don't think they are likely to get much better than that, the joints are usually slightly visible. Maybe a bit of filler to hide the joint better? The cut in the stone is fresh, that's the problem

tulips27 · 12/12/2021 13:52

It might look worse over time if debris gets caught. It's a tough one, always difficult to raise a complaint, isn't it?

Doodar · 12/12/2021 13:42

Awful, should be one piece

Loudestcat14 · 12/12/2021 13:36

I wouldn't accept that. If it does have to have a join, the marble effect should at least be matched up to run in the same direction. Was it pre-cut by the supplier or by the fitter? If it's latter, you'll have more recourse because they shouldn't have sent such a shoddy match. If it's the fitter, it's trickier, because you might have to get them to cover the cost of a new worktop if they can't salvage it.

Theblacksheepandme · 12/12/2021 13:32

It looks terrible but everything can be sorted. Have they been paid already? You will have more control of the situation if they haven't.

WhatsitWiggle · 12/12/2021 13:31

They don't look the same level. Can you feel a ridge when you run your hand over the join? Or is it the glue that's visible?

justaweeone · 12/12/2021 13:17

It's shocking!
Hope you can get it sorted out.

TiddleTaddleTat · 12/12/2021 13:04

Is this marble or laminate ?

Zilla1 · 12/12/2021 13:00

Two issues, the quality of the joint and the odd decision to orient the two pieces of the joints in different 'marble flow' directions. I would not accept the latter approach.

Ozanj · 12/12/2021 12:56

You shouldn’t need joins unless you’re using granite and have a really large space to cover. The fact that they gave them to you in such a small space suggests they’re probably using offcuts from someone else’s kitchen. I’d be raising hell about this.

Lonelycrab · 12/12/2021 12:53

Yes the curve is normal, all corner joins I have ever seen are curved like that.

It looks like whatever did the cut wasn’t sharp, typical ragged edges you get when a blade gets blunt. Personally I could live with that though, just looks a bit scrappy when you look closely.

LookItsMeAgain · 12/12/2021 12:42

Nope - I wouldn't be happy with that at all. Why does there have to be a join there at all? Couldn't they cut it out of the one piece and to fit the area required? There was no attempt at even making the grain in the surface flow the same way. Really poorly done.

junglejane66 · 12/12/2021 12:26

@LazyDoll

Agree with pp. Also why isn’t the cut straight? I don’t understand the need for the curve Confused
You need the curve, there isnt anyway it would fit otherwise, you cant do a straight line, it just wouldn't work, unless you know how to do it? If its a laminate top, then they use a jig to cut it
HoardingSamphireSaurus · 12/12/2021 12:26

When you discussed the worktop there should have been a discussion about the joins. It costs more to have them mitred into the corners - and that's probably what you were expecting.

Have a chat with them, but it would mean replacing most, if not all, of it.

LittleDandelionClock · 12/12/2021 12:17

Where the curve is - as a pp said - it looks a bit ropey. Not shit, but a bit ropey. If my DH or dad had done it, I would be OK with it I guess, but this is not really acceptable for a professional job tbh.

ForeverQuery · 12/12/2021 12:14

No I definitely can't live with that, it's stressing me out looking at it because it's so obvious
Thanks for clarifying that it's awful and I'll be on the phone first thing tomorrow
I had so much going on when they'd done it I didn't really notice at first but now it's the first thing I see when I go in to the kitchen!

OP posts:
Thatldo · 12/12/2021 12:06

Sorry,it looks awful.I would not accept that botch.the marble effect looks "against the grain" where it meets and the cut looks wonky.was it a professional who did this job?

Londoncatshed · 12/12/2021 12:05

I wouldn’t be happy with this. Did they ask if you were happy about the marble running the opposite way? I wouldn’t be. The join isn’t good either. I suppose it depends on how much you paid and if they discussed with you.

billyt · 12/12/2021 12:05

I doubt you'd get the marbling to line up as it runs along the worktop so where it meets at 90 degrees will always be a bit of a mis-match

LazyDoll · 12/12/2021 12:04

Agree with pp. Also why isn’t the cut straight? I don’t understand the need for the curve Confused

billyt · 12/12/2021 12:04

curve not cure